| Microsoft DirectX 8.1 (Visual Basic) |
There are two ways to encode texture maps that exhibit more complex transparency. In each case, a block that describes the transparency precedes the 64-bit block already described. The transparency is either represented as a 4x4 bitmap with four bits per pixel (explicit encoding), or with fewer bits and linear interpolation that is analogous to what is used for color encoding.
The transparency block and the color block are arranged as shown in the following table.
| Word Address | 64-bit Block |
|---|---|
| 3:0 | Transparency block |
| 7:4 | Previously described 64-bit block |
For explicit texture encoding (DXT2 and DXT3 formats), the alpha components of the texels that describe transparency are encoded in a 4x4 bitmap with 4 bits per texel. These four bits can be achieved through a variety of means such as dithering or by simply using the four most significant bits of the alpha data. However they are produced, they are used just as they are, without any form of interpolation.
The following diagram shows a 64-bit transparency block.
Note The compression method of Microsoft® Direct3D® uses the four most significant bits.
The following tables illustrate how the alpha information is laid out in memory, for each 16-bit word.
This table contains the layout for Word 0.
| Bits | Alpha |
|---|---|
| 3:0 (LSB) | [0][0] |
| 7:4 | [0][1] |
| 11:8 | [0][2] |
| 15:12 (MSB) | [0][3] |
This table contains the layout for Word 1.
| Bits | Alpha |
|---|---|
| 3:0 (LSB) | [1][0] |
| 7:4 | [1][1] |
| 11:8 | [1][2] |
| 15:12 (MSB) | [1][3] |
This table contains the layout for Word 2.
| Bits | Alpha |
|---|---|
| 3:0 (LSB) | [2][0] |
| 7:4 | [2][1] |
| 11:8 | [2][2] |
| 15:12 (MSB) | [2][3] |
This table contains the layout for Word 3.
| Bits | Alpha |
|---|---|
| 3:0 (LSB) | [3][0] |
| 7:4 | [3][1] |
| 11:8 | [3][2] |
| 15:12 (MSB) | [3][3] |
The difference between DXT2 and DXT3 is that in the DXT2 format it is assumed that the color data has been premultiplied by alpha. In the DXT3 format it is assumed the color is not premultiplied by alpha. These two formats are needed because in most cases by the time a texture is used, simply examining the data is not sufficient to determine if the color values have been multiplied by alpha. Because this information is needed at run time, the two FOURCC codes are used to differentiate these cases. However, the data and interpolation method used for these two formats is identical.
The color compare used in DXT1 to determine if the texel is transparent is not used in this format. It is assumed that without the color compare the color data is always treated as if in 4-color mode. In other words, the if statement at the top of the DXT1 code should be the following:
if ((color_0 > color_1) OR !DXT1) {
The encoding of transparency for the DXT4 and DXT5 formats is based on a concept similar to the linear encoding used for color. Two 8-bit alpha values and a 4x4 bitmap with three bits per pixel are stored in the first eight bytes of the block. The representative alpha values are used to interpolate intermediate alpha values. Additional information is available in the way the two alpha values are stored. If alpha_0 is greater than alpha_1, then six intermediate alpha values are created by the interpolation. Otherwise, four intermediate alpha values are interpolated between the specified alpha extremes. The two additional implicit alpha values are 0 (fully transparent) and 255 (fully opaque).
The memory layout of the alpha block is as follows:
| Byte | Alpha |
|---|---|
| 0 | Alpha_0 |
| 1 | Alpha_1 |
| 2 | [0][2] (2 LSBs), [0][1], [0][0] |
| 3 | [1][1] (1 LSB), [1][0], [0][3], [0][2] (1 MSB) |
| 4 | [1][3], [1][2], [1][1] (2 MSBs) |
| 5 | [2][2] (2 LSBs), [2][1], [2][0] |
| 6 | [3][1] (1 LSB), [3][0], [2][3], [2][2] (1 MSB) |
| 7 | [3][3], [3][2], [3][1] (2 MSBs) |
The difference between DXT4 and DXT5 is that in the DXT4 format it is assumed that the color data has been premultiplied by alpha. In the DXT5 format, it is assumed the color is not premultiplied by alpha. These two formats are needed because, in most cases, by the time a texture is used simply examining the data is not sufficient to determine if the color values have been multiplied by alpha. Because this information is needed at run time, the two FOURCC codes are used to differentiate these cases. However, the data and interpolation method used for these two formats is identical.
The color compare used in DXT1 to determine if the texel is transparent is not used with these formats. It is assumed that without the color compare the color data is always treated as if in 4-color mode. In other words the if statement at the top of the DXT1 code should be:
if ((color_0 > color_1) OR !DXT1) {