ID Number: Q76869
2.00c
MS-DOS
Summary:
This article describes how to install and set up a server for remote
booting MS-DOS under LAN Manager version 2.0c. It is assumed in this
article that LAN Manager 2.0c is installed on the server in the
C:\LANMAN directory, and the workstation to be booted is named
DEFAULT. To perform some of the steps below, you must be logged on
with an account that has ADMIN privileges.
Hardware required on the workstation is a Western Digital Remote Boot
ROM for LAN Manager 2.0 installed on a Western Digital Ethercard Elite
(WD8003EP). Make sure a LAN Manager server is installed, and have the
following items available: LAN Manager install disks (OS/2 and DOS),
the LAN Manager Patch 9 disks, a blank floppy disk, and MS-DOS version
5.0.
More Information:
Procedures for Installation and Setup
-------------------------------------
1. Make sure the server name is not more than eight characters in
length. Also, be sure there is at least 10 megabytes (MB) free on
the server's hard drive for the initial setup, and one RPL
workstation.
2. On the server, use LAN Manager's Setup program to add the
REMOTEBOOT protocol along with NetBEUI to the Ethernet card
driver. Save the configuration and exit Setup.
3. Edit CONFIG.SYS as follows:
a. Add "SET TMP=C:\TMP" (without the quotation marks) to the end of
CONFIG.SYS.
b. Add "C:\LANMAN\DRIVERS\PROTOCOL\RPL;" after "LIBPATH=" in
CONFIG.SYS.
c. If the line "DEVICE=COM01.SYS" or "DEVICE=COM02.SYS" appears in
CONFIG.SYS, make sure this driver is listed before
"DEVICE=RDRHELP.SYS".
d. Save CONFIG.SYS and exit the editor.
4. Make the directory C:\TMP (type "md c:\tmp").
5. Edit C:\LANMAN\LANMAN.INI as follows:
a. In the [server] section, make the following changes:
1) For "maxopens", add 50 for each RPL workstation.
2) Set "maxconnections" to twice the value of maxopens.
3) Set "maxlocks" to the value of maxopens.
4) Set "maxsessopens" to the value of maxopens.
b. In the [remoteboot] section, make sure the RPL1 line reads as
follows:
rpl1 = ethnet1.dll ethnet2.dll ethoem.dll 0
Place a semicolon in front of any other RPL1 or RPL2 lines in
this section to comment out those lines.
c. Save LANMAN.INI and exit the editor.
6. From the C:\LANMAN directory, run RPLSETUP. Choose the DOS option.
Install to C:\LANMAN.
7. Edit C:\LANMAN\RPL\DOS\LANMAN.INI. Change the "domain =" entry to
match the server's domain.
8. Verify the interrupt and base address settings for the workstation
in C:\LANMAN\RPL\DOS\MACWD\PROTOCOL.INI.
9. Edit C:\LANMAN\RPL\RPL.MAP as follows:
a. Comment out (using a semicolon) the first two server records
(the ones that begin with yyyyyyyyyyyy) and the last record.
Leave the record that refers to DOSBBETH.CNF in field 2.
b. Change all occurrences of "RPLSERVR" to the name of the server.
c. Comment out (using a semicolon) all of the workstation records.
(These are at the bottom of the file and begin with 10005A and
0000C0.)
d. Add the following workstation record to the bottom of the file:
0000C0?????? DEFAULT ~ DOS500 <servername> ~~~~,,, Z R_DOSETH ~ ~
Note: Replace "<servername>" with the name of the server.
10. From Patch 9 disk 2, copy
A:\DRIVERS\PROTOCOL\NETBEUI\NETBEUI.DOS
to
C:\LANMAN\RPL\DOS\NETBEUI.DOS
11. On the server, make the directory C:\LANMAN\RPL\DOS500.
12. Copy any DOS files to that directory from the MS-DOS 5.0 machine.
(For example, copy any DOS utilities that will be used on the RPL
workstation, such as CHKDSK.EXE.)
13. On a machine running MS-DOS 5.0, format a 1.2 MB system floppy
disk (type "format /s a:").
14. Copy A:\COMMAND.COM from the system disk to C:\LANMAN\RPL\DOS500.
15. Change to the C:\LANMAN\RPL\DOS directory. Insert the DOS 5.0
system formatted disk into drive A of the server. At the OS/2
command prompt, type "makeimg dos500" (without the quotation
marks).
16. For user-level security, at the command line, type:
net accounts /minpwlen:0
net group rpl /add
net user default /add /passwordreq:no
/workstations:default
net group rpl default /add
Enter the Net Admin Screen and assign the following permissions
for DEFAULT to the following trees:
Permission Tree
---------- ----
RWCDXA C:\LANMAN\RPLUSER\DEFAULT
(Be sure to use <PERMIT TREE>.)
Give to the group RPL the following permissions to the following
trees:
RX C:\LANMAN\RPL
(Be sure to use <PERMIT TREE>.)
17. Shut down and reboot the server.
18. If the RPL workstation has a hard drive, copy
C:\LANMAN\RPL\DOS\RPLENABL.EXE to a floppy disk, insert the floppy
disk in the workstation's disk drive, and run RPLENABL.EXE on the
workstation.
19. When the server has booted and the SERVER service has started,
type "net load rpl" at the OS/2 command line.
20. On the server, start the remote boot service by typing:
net start rpl
21. Power up the RPL workstation. The boot process will begin.
Customizing the Installation
----------------------------
The following files are used to configure the workstation:
C:\LANMAN\RPL\DOS\MACWD\PROTOCOL.INI
C:\LANMAN\RPL\DOS\AUTOEXEC.BAT
C:\LANMAN\RPL\DOS\CONFIG.SYS
C:\LANMAN\RPL\DOS\AUTOEXEC.BAT
C:\LANMAN\RPL\DOS\SETVAR.BAT
C:\LANMAN\RPL\DOS\DOS500.DEF
Note: If any of the above files are modified (with the exception of
PROTOCOL.INI), a new disk image must be made (step 13).
The following information is an example of how to install device
drivers (for example, HIMEM.SYS) on the workstation:
1. Copy HIMEM.SYS from a DOS workstation to C:\LANMAN\RPL\DOS.
2. Edit C:\LANMAN\RPL\DOS\CONFIG.SYS and add "DEVICE=HIMEM.SYS".
3. Edit C:\LANMAN\RPL\DOS\DOS500.DEF and add the following line to the
end of the file:
HIMEM.SYS A:\HIMEM.SYS
4. Insert the DOS 5.0 system formatted disk in drive A on the server.
At the OS/2 command prompt, type "makeimg dos500".
Additional reference words: 2.00c 5.00