How To Configure Windows 95 to Dial into a RAS/RRAS Server

Last reviewed: February 17, 1998
Article ID: Q178729
The information in this article applies to:
  • Microsoft Windows NT Workstation version 4.0
  • Microsoft Windows NT Server version 4.0
  • Microsoft Windows 95

SUMMARY

This article discusses a step-by-step procedure that ensures Windows 95 TCP/IP client platforms will successfully dial, get connected, and log on to a computer running Windows NT Server version 4.0 Remote Access Service (RAS) or Routing and Remote Access Service (RRAS). These steps also enable the Windows 95 Dial- Up Networking (DUN) Client to successfully browse the network beyond the RAS or RRAS Server.

MORE INFORMATION

NOTE: The following information assumes that RAS/RRAS has been installed and configured to support Dial-up Clients using TCP/IP and allows access to the entire network.

  1. Upgrade your Windows 95 DUN Client to Version 1.2b, which can be found at the following location:

          http://www.microsoft.com/communications/PPTPdownload1.htm
    

    NOTE: Because the Microsoft Web site is constantly updated, the site address may change without notice. If this occurs, link to the Microsoft home page at the following address:

          http://www.microsoft.com/
    

    How to tell if you have the 1.2b package:

        - The file version of Msdun12.exe reports 4.10.1538
    

        - The product version of the Msdun12.exe reports 1.2b
    

        - The binaries in the Msdun12.exe package are time/date stamped with
          the following:
    

             9/16/97     2:20PM
    
       For more information, see the following articles in the Microsoft
       knowledge base:
    
          ARTICLE-ID: Q154434
          TITLE     : Err Msg: No Domain Controller Was Available to
                      Validate...
    
          ARTICLE-ID: Q166288
          TITLE     : Dial-Up Networking 1.2 Dun12.doc File
    
       NOTE: The two RAS updates mentioned in Q154434 have been incorporated
       into the DUN 1.2B Upgrade.
    
    

  2. If there is a network interface card (NIC) in your Windows 95 DUN Client, create a hardware profile that disables the NIC card.

    For more information, see the following article in the Microsoft knowledge base:

          ARTICLE-ID: Q141600
    
          TITLE     : How to Manually Create Hardware Profiles for Laptop
                      Computers
    
          ARTICLE-ID: Q150053
          TITLE     : Erratic Domain Logon from Windows 95 Dial-Up Networking
    
       NOTE: Microsoft Windows 95 disables the hardware bus slot. If you have a
       multi-function NIC/Modem, you will disable both functions. OSR2 has the
       capability to disable the individual function of the card instead of the
       entire bus.
    
       If Windows 95 is loaded on a laptop with docking station, undocking will
       accomplish the same result as a hardware profile. If the NIC is a PC
       Card, simply remove the card from the PCMCIA slot.
    
    

  3. Domain authentication and browsing only occur when the Windows 95 DUN Client can find the primary domain controller (PDC) for the Windows NT domain. The following two things must exist for this to occur:

    a. NetBIOS Name Resolution must be implemented. This is accomplished by

          either installing a Windows Internet Name Service (WINS) Server on
          the network or using an Lmhosts file to resolve the NetBIOS name of
          the PDC. This is used for both domain validation and obtaining a
          browse list.
    

    b. The Windows 95 workgroup name must be the same as the Windows NT

          domain name. This is defined in the Network Identification Tab in
          Network Neighborhood properties.
    

    For more information, see the following article in the Microsoft knowledge base:

          ARTICLE-ID: Q150800
    
          TITLE     : Domain Browsing with TCP/IP and LMHOSTS Files
    
    
Dial-up connections are generally slow when you browse over a dial-up connection. Depending on the location of the PDC and the size of the domain, it can take a considerable amount of time to obtain a browse list from the PDC.
Keywords          : nthowto ntinterop ntnetserv ntras NTSrvWkst win95 kbinterop kbnetwork
Version           : WinNT:4.0;Windows:95
Platform          : WINDOWS


================================================================================


THE INFORMATION PROVIDED IN THE MICROSOFT KNOWLEDGE BASE IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. MICROSOFT DISCLAIMS ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL MICROSOFT CORPORATION OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL, LOSS OF BUSINESS PROFITS OR SPECIAL DAMAGES, EVEN IF MICROSOFT CORPORATION OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SO THE FOREGOING LIMITATION MAY NOT APPLY.

Last reviewed: February 17, 1998
© 1998 Microsoft Corporation. All rights reserved. Terms of Use.