XCLN: Using ShivaRemote with Exchange (Win 3.x/LanMan NetBEUI)

• Microsoft Exchange Windows 3.x client, versions 4.0 and 5.0

SUMMARY

A white paper on ShivaRemote is located on Microsoft TechNet and can also be found on the following World Wide Web location:

   http://www.microsoft.com/ExchangeSupport/

(For information about setting up Shiva for use over other protocols, see the Reference section below).

MORE INFORMATION

To configure your computer so that you can use ShivaRemote:

1. Install MS-DOS on your computer.

2. Install Microsoft LAN Manager 2.2 Full Redirector (LanMan software is located on the Windows NT 3.51 Server compact disc in the Clients\Lanman\disks directory).

3. Install Microsoft Windows 3.1.

4. Install Microsoft Exchange Windows 3.x client.

5. Run the ShivaRemote Setup program from the Microsoft Exchange program group.

6. When ShivaRemote Setup is complete, restart your computer so that the configuration changes you made take effect.

7. After your computer restarts, make the following changes to Config.sys

       and Protocol.ini:
   

       Config.sys:
   

          DEVICE=C:\SHIVA\DIALNDIS.EXE    <- Add this line.
   
       Protocol.ini:
   
       NOTE: The name of the NETBEUI section below may vary.  The "T1" entry
       specifies the main NETBEUI time-out value; 8000 specifies 8 seconds.
   
          [NETBEUI]
          ; BINDINGS = "UBNEITP_NIF"      <- Make this line a comment.
          BINDINGS=SDIALIN$               <- Add this line.
          T1=8000                         <- Add this line.
          [SDIALIN$]                      <- Add this line.
          DriverName=SDIALIN$             <- Add this line.
   
   

8. Your computer should be configured for ShivaRemote dial-in. Restart your computer again, and watch for error messages as the computer starts.

9. You must log on to the network before starting the Microsoft Exchange client. If you are not connected to the network when you log on to the network, LAN Manager will display the following message:

         You are logged on, but have not been validated by a server.
         Therefore, you may not have permission to use some network
         resources.
   

10. Click OK and proceed.

To configure LAN Manager, use one of the following methods:

• Configure LAN Manager using the Setup program, as follows:

  1. Run the LAN Manager Setup program (Setup.exe) in your LAN Manager

        directory (C:\Lanman.dos).
  

  2. On the Configuration menu, click Workstation Settings.

  3. In the Workstation Settings dialog box, click OK.

  4. In the Support For Windows Environment dialog box, click Yes and

        click OK.
  

  5. In the Windows Directory dialog box, type the directory where Windows

        is installed (by default C:\Windows) and click OK.
  

  6. In the Memory Management dialog box, choose your memory management

        settings and click OK.
  

  7. On the LAN Manager menu, click Exit Setup.

  8. Restart your computer.

• Add the following commands to your Autoexec.bat file (or type the commands at the MS-DOS prompt):

        net start workstation
        load networking_protocols
        net logon username
  

  Once you have the above setup, restart and ensure you receive no error messages when booting with the newly configured Autoexec.bat and Config.sys.

1. Install the Microsoft Exchange Windows 3.x client software (run Setup from the Microsoft Exchange Windows 3.x client compact disc or from a sharepoint). Select Custom install and verify that Shiva is selected. (Setup will create a "ShivaRemote setup" icon in the Microsoft Exchange Program group).

2. If possible, verify a valid Exchange mailbox/account exists while connected to the LAN. (Start the Microsoft Exchange client, create a profile and make sure you can log on to your mailbox and send a piece of mail to yourself).

1. Run "ShivaRemote setup" from the Microsoft Exchange Program group.

2. Click OK to Install ShivaRemote.

3. Select the port and your specific modem manufacturer/model.

4. Specify a Description, Dial-in-Name (NT account that has been granted dial-in access on the server), Password (Password for the NT Account you are dialing in on), and Phone number.

1. Dial the computer running RAS. (Microsoft Exchange is supported dialing into either a computer running Windows NT Server with RAS or a Shiva LanRover.)

2. Once connected, minimize ShivaRemote Connect

3. Start the Microsoft Exchange Windows 3.x client (online, as a test). Type the User Name (Exchange Mailbox Name), the Password (Windows NT Domain Password), and the Domain (Windows NT Domain Name that your account is in) and verify you can be properly logged on.

   If the above step allows you to properly send/receive mail, Shiva and Microsoft Exchange are configured correctly.

To setup the Microsoft Exchange client to automatically dial while working offline :

1. In Control Panel/Mail-Fax, select the properties for Exchange Server in the profile and on the "dial up networking" tab

2. Select the Shiva connection name that was tested in step 1 under "dial using the following connection."

3. Type the user name, password, and domain name in the dialog box.

REFERENCE

Updated modem scripts for use with ShivaRemote can be found on Shiva's web page at www.shiva.com under "support"/modem scripts.

Additional configuration information may also be found in the config.hlp file installed during installation of the ShivaRemote software.

For more information about specific remote options with the Microsoft Exchange Windows 3.x client, see the following article in the Microsoft Knowledge Base :

   ARTICLE-ID: Q139934
   TITLE     : XCLN: The Microsoft Exchange Client and Mobile Users

   ARTICLE-ID: Q158124
   TITLE XCLN: ShivaRemote with Exchange - RAS Server Considerations

   ARTICLE-ID: Q158074
   TITLE XCLN: Using ShivaRemote with Exchange (DOS/real-mode IPX)

   ARTICLE-ID: Q157740
   TITLE XCLN: Using ShivaRemote with Exchange (DOS/LanMan TCP/IP)

   ARTICLE-ID: Q158077
   TITLE     : Using ShivaRemote with Exchange (Windows 3.x/real-mode IPX)

   ARTICLE-ID: Q158111
   TITLE XCLN: ShivaRemote with Exchange (WFW 3.11/WFW TCP/IP or
               NetBEUI)