XCLN: Can't Change Password on Novell Client

ID: Q148420


The information in this article applies to:
  • Microsoft Exchange Windows 3.x client, versions 4.0, 5.0
  • Microsoft Exchange Windows 95/98 client, versions 4.0, 5.0
  • Microsoft Exchange Windows NT client, versions 4.0, 5.0
  • Microsoft Outlook for Windows 3.x, Exchange Server Edition, version 8.0
  • Microsoft Outlook Windows 95/98 client, versions 8.0, 8.01, 8.02, 8.03, 8.04, 8.5, 9.0
  • Microsoft Outlook Windows NT client, versions 8.0, 8.01, 8.02, 8.03, 8.04, 8.5, 9.0


SYMPTOMS

When you try to change the password on a Microsoft Exchange or Outlook client that is logging on to a Novell server and not being authenticated by a Windows NT server at bootup, the following error message may occur:

The NT Domain password could not be changed. A required action was not successful due to an unspecified error.
This may also occur with other clients running on other operation systems and networking software using TCP/IP or IPX as their protocol.


RESOLUTION

To resolve this problem, do the following:

  1. For NetWare clients, install the Gateway Services for NetWare on the primary domain controller (PDC), which has the Microsoft Exchange user accounts.


  2. Ensure that the client is running the latest version of the networking files from the software provider.


  3. Ensure that the Remote Procedure Call (RPC) service is configured to start automatically. This can be changed in Control Panel Services.

    WARNING: Using Registry Editor incorrectly can cause serious problems that may require you to reinstall Windows NT. Microsoft cannot guarantee that problems resulting from the incorrect use of Registry Editor can be solved. Use Registry Editor at your own risk.

    NOTE: Normally, registry entries are not case sensitive. However, in the case of both of these entries, they are case sensitive. When adding these new keys, be sure to match the case exactly as it is shown in Step 5.


  4. Ensure that the registry on the PDC has the following entries. If these entries are missing, add them according to the instructions in Step 5. Look for the entries at the following registry key:
    
          HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\LSA 

    If the PDC has NWLink installed, the entry should be:
    
          NetWareClientSupport:REG_DWORD:0x1 

    If the PDC has TCP/IP installed, the entry should be:
    
          TcpipClientSupport:REG_DWORD:0x1 

    WARNING: Using Registry Editor incorrectly can cause serious problems that may require you to reinstall Windows NT. Microsoft cannot guarantee that problems resulting from the incorrect use of Registry Editor can be solved. Use Registry Editor at your own risk.


  5. Add the registry values to the PDC because it is here that the Windows NT password is changed. To add the values:


    1. Start Registry Editor (Regedt32.exe).


    2. Under the HKEY_LOCAL_MACHINE subtree, go to the following subkey:
      
            SYSTEM\CurrentControlSet\Control\LSA 


    3. On the Edit menu, click Add Value.


    4. If NWLink is installed on the PDC, type NetWareClientSupport under Field Type.


    5. In the Data Type field, choose REG_DWORD, and click OK.


    6. In the DWORD editor, in the Data field, type 1.


    7. Click OK. The new value should appear as an entry.


    8. Repeat steps a through f for TcpipClientSupport if TCPIP is installed on the PDC.


    9. Restart the PDC for the changes to take effect.


Additional query words: password change faq

Keywords : kbenv XCLN
Version : WINDOWS:4.0,5.0,8.0,8.01,8.02,8.03,8.04,8.5,9.0
Platform : WINDOWS
Issue type : kbprb


Last Reviewed: May 25, 1999
© 2000 Microsoft Corporation. All rights reserved. Terms of Use.