XCON: Messages Queue Over X.400 Connectors Through Firewall

ID: Q196381

The information in this article applies to:

Microsoft Exchange Server, versions 4.0, 5.0, 5.5

SYMPTOMS

Mail flow may be slow and seemingly sporadic over X.400 connectors through a Raptor Firewall (version 5.x or greater). Messages may accumulate on the Message Transfer Agent (MTA) on the Exchange Server computer that is outside the Raptor firewall. However, the external Exchange Server computer's queued up messages are delivered after the internal Exchange Server computer contacts the external Exchange Server computer to deliver a mail message.

The external Exchange Server computer attempts to initiate the connection with the internal Exchange Server computer, then typically fails. Failure of the attempted connection, results in one or more of the following events being logged in the Windows NT Application Event log:


   MSExchangeMTA Event ID: 1290
   Type: Warning
   Category: X.400 Service
   A locally initiated association to
   /O=OrganizationName/OU=SiteName/CN=Configuration/CN=Connections
   /CN=ConnectorName was refused. The failure reason provider was 0 and the
   reason was 0. Control block index 202. Type 1. [PLATFORM KERNEL 20 130]
   (12)

   MSExchangeMTA Event ID: 289
   Type: Warning
   Category: X.400 Service
   A connection to   /O=OrganizationName/OU=SiteName/CN=Configuration
   /CN=Connections/CN=ConnectorName could not be opened. [MTA XFER-IN 17
   26] (12)

   MSExchangeMTA Event ID: 1294
   Type: Warning
   Category: X.400 Service
   An association with entity
   /O=OrganizationName/OU=SiteName/CN=Configuration
   /CN=Connections/CN=ConnectorName ended abnormally. [198 1 0 1 PLATFORM
   KERNEL 20 130] (10)

The internal Exchange Server computer will log the following Event:


   MSExchangeMTA Event ID: 1293
   Type: Warning
   Category: X.400 Service
   A remotely-initiated association from
   /O=OrganizationName/OU=SiteName/CN=Configuration/CN=Connections
   /CN=ConnectorName was refused. The failure reason provider is 0 and the
   reason is 0. Control block index 1. Type 1. [PLATFORM KERNEL 26 128]
   (12)

CAUSE

Event ID 1290 indicates that the MTA on the external Exchange Server computer attempted to communicate with the MTA on the internal Exchange Server computer and was refused by the internal Exchange Server computer's MTA.

The internal Exchange Server computer will log Event ID 1293 when the external Exchange Server computer attempts to communicate with it. This event indicates that the MTA on the internal Exchange Server was contacted by the external Exchange Server computer's MTA and the internal Exchange Server computer's MTA had refused the connection.

WORKAROUND

To work around this problem, use one of the three methods below:

The best option is to remove the Generic Service Passer from the firewall that is listening on TCP port 102. Then enable a local tunnel on the Raptor firewall so that connections between the two Exchange Server computers over TCP port 102 are simply routed through the firewall. In this scenario, the X.400 connectors will need to be configured to point directly to either the IP address or to fully qualified domain name (FQDN) of the remote Exchange Server computer.

Create a second X.400 connector on the internal Exchange Server computer that matches the pre-existing X.400 connector in every property page except the Schedule and Stack property pages. The Schedule should be set to remote-initiated, and the Stack property page should be configured to point to either the IP address or to the FQDN of the external Exchange Server computer. Also, the cost of this connector should set to 99. By doing this, the internal Exchange Server computer will not reject the connection requests of the external Exchange Server computer. Therefore, mail flow should become consistent and steady.

Disable the client-side transparency feature on the firewall. This may present a problem for customers that want other internal servers, such as http servers, to be able to log the actual IP address of the external client.

MORE INFORMATION

It is required that both of the internal Exchange Server computer's and the external Exchange Server computer's X.400 connector be scheduled for always. This is can be configured on the Schedule Property Page of the X.400 Connector.

Because the firewall is configured to proxy communications that come in on TCP port 102, both the internal Exchange Server computer's and the external Exchange Server computer's X.400 connectors are configured to communicate with the firewall and not directly to each other. This can be done by placing either the FQDN or the IP address of the firewall on the X.400 connector's Stack Property page.

Both the internal Exchange Server computer's and the external Exchange Server computer's X.400 connectors are configured to allow two-way alternate on the Advanced Property Page of the X.400 connector.

The problem stems from a feature or option available in Raptor Eagle firewall, version 5.x and later. The feature is called Client-side Transparency. It allows the inbound IP packets to not be re-written with the firewall's internal IP address. Therefore the source IP address is the IP address of the external client that is making the connection. This feature is not enabled by default. The default behavior of the Raptor Eagle firewall is to re-write the inbound IP packet so that the packet appears to be coming from the firewall's internal network interface.

What this means to the Exchange Server X.400 connectors:

The Raptor firewall must be configured to proxy connections over TCP port 102. This requires that both the internal Exchange Server computer's and the external Exchange Server computer's X.400 connectors are configured to communicate with the firewall's internal and external network interfaces, respectively, and not directly to each other. This is done by placing either the FQDN the IP address of the firewall on the X.400 connector's Stack Property page. The problem arises when the external Exchange Server computer attempts to connect to the internal Exchange Server computer. With the Client-transparency feature enabled, the firewall leaves the source IP address in the inbound packet untouched. Because the internal Exchange Server computer's X.400 connector is configured to accept connections from the firewall's internal IP address, it rejects the connection request from the external Exchange Server computer. However, when the internal Exchange Server computer initiates the conversation, the firewall does re-write the outbound packet with the firewall's external IP address. Because the external Exchange Server computer's X.400 connector is configured to communicate with the external interface of the firewall, the connection is allowed and mail is delivered. Because the X.400 connectors on both servers are set to two-way alternate, the internal Exchange Server computer also "picks" up the messages that the external Exchange Server computer has queued up for it.

Additional query words: firewall Raptor Eagle 1290 1293

Keywords :
Version : WinNT:4.0,5.0,5.5
Platform : winnt
Issue type : kbprb