Contents of the ActiveSync 3.0 Readras.doc File

• Microsoft ActiveSync 3.0

SUMMARY

This article contains a copy of the information in the Readras.doc file included with ActiveSync 3.0.

MORE INFORMATION

Calling a Desktop Computer's Modem from your Mobile Device

• These instructions are approximate steps intended for experienced users only. Depending on the system configuration, other steps may be required, or some of the steps outlined may not be necessary. If you are not familiar with network component installation and configuration, you should consult your system administrator.



• Installing and configuring Remote Access Service (RAS) and Dial-up Networking (DUN) to work with ActiveSync may disable other types of ActiveSync connections, such as serial cable and cradle. Automatic baud rate detection will also be disabled.



• If you disable serial connection, RAS and DUN will not be disabled. You must separately disable network and RAS connections under Connections Settings on the File menu



• These procedures may interact with your existing network configuration (for example, dial-out modems) or require removal of proxy software to work properly.



• The instructions for Windows 2000 are for Beta 3. The final product may require slightly different steps.

• Set up a partnership between your device and desktop computer using a serial cable, cradle, or infrared connection. For more information about setting up a partnership, see Microsoft ActiveSync Help.



• If your computer is running Windows NT 4.0, you need to install the Remote Access Service (RAS). RAS is installed as a part of all Windows 2000 installations.



• If your desktop computer is running Windows 95, you need to install Dial-Up Networking Upgrade (DUN) 1.3 or later which is available at: http://www.microsoft.com/Windows95/downloads/. The following procedures will not work with DUN 1.2.



• Install an internal or external modem for your desktop computer and configure it for general use as instructed in Windows Help or your modem instructions.



• Install an internal modem, PC Card modem, or external modem for your device.

Configure RAS, DUN, and modem equipment to work with ActiveSync

1. Install network components for a PC without a network card.

2. Configure RAS.

3. Configure the user account.

1. Click Start, Settings, and then Control Panel.

2. Double-click the Network icon. If you see a Network Configuration Wizard, then continue below. Otherwise, skip to the next section because networking is already installed.

3. In the Network Configuration dialog box, click Yes.

4. In the Network Setup Wizard, select Wired to the network, clear Remote access to the network, and then click Next.

5. Click Select from list.

6. In the Network Adapters box, select MS Loopback Adapter and click Next.

7. In the Network Protocols box, select TCP/IP Protocol and clear all other options.

8. Click Next three times to start installing the selected components.

9. In the Windows NT Setup dialog box, enter the directory where your Windows NT source files are located, and then click Continue.

10. In the MS Loopback Adapter Card Setup dialog box, click Continue. The default frame type will be selected.

11. In the TCP/IP Setup dialog box, click No when asked to use DHCP.

12. In the Microsoft TCP/IP Properties dialog box, click the IP Address tab.

13. Ensure MS Loopback Adapter is selected.

14. Click Specify an IP Address.

15. In the IP Address box, enter 1.1.1.1.

16. In the Subnet Mask box, enter 0.255.255.255.

17. Ensure the Default Gateway box is cleared.

18. Click Next on the next three dialog boxes, and then click Finish to complete the Networking Wizard.

19. Restart your desktop computer.

1. Click Start, Settings, and then Control Panel.

2. Double-click the Network icon, and then click the Services tab.

3. From the Network Services list, select Remote Access Service, and then click Properties. If Remote Access Service is not listed, perform the following steps; otherwise, proceed to step 9:

4. Click the Services tab, and then click Add.

5. Select Remote Access Service from the list, and then click OK.

6. If necessary, provide your Windows NT Setup disks as instructed.

7. In the Add RAS Device dialog box, select your modem.

8. Click OK, then leave the Remote Access Setup dialog box open.

9. In the Remote Access Setup dialog box, select your modem.

10. Click Configure, select Receive calls only, and then click OK.

11. In the Remote Access Setup dialog box, click Network.

12. In the Network Configuration dialog box, clear Require data encryption.

13. Under Server Settings, select TCP/IP, and then click Configure.

14. Select This computer only.

15. Select Use static address pool.

16. In the Begin box, enter 192.168.55.100.

17. In the End box, enter 192.168.55.112.

18. Clear Allow remote clients to request a predetermined IP address.

19. Accept the default (recommended) responses for any messages that appear.

20. Click Continue, and then click Close.

21. Restart your desktop computer when prompted.

22. Reinstall any Windows NT 4.0 Service Packs.

1. Click Start, Programs, Administrative Tools, and then User Manager.

2. In the top list box, double-click your user account.

3. Clear Account Disabled, and then clear User Must Change Password at Next Logon.

4. Select Password Never Expires.

5. Delete any passwords in the Password and Confirm Password boxes.

6. Click Dialin.

7. Select Grant dialin permission to user and No Call Back.

Configure the desktop computer for incoming connections

1. Click Start, Settings, and then Control Panel.

2. Double-click the Network and Dial-up Connections icon.

3. Click Make New Connection.

4. Select Accept incoming connections and click Next.

5. Select the modem from the list of devices, and click Next.

6. Select either of the options for allowing Virtual Private Connections, and click Next.

7. Check the users you want to be able to authenticate when connecting to the desktop from the device, and click Next.

8. Ensure the Internet Protocol (TCP/IP) check box is selected, click Next, and then Finish.

To call a modem attached to a desktop computer running Windows 95/98:

1. Install Dial-Up Adapter networking components.

2. Ensure the Dial-Up Adapter is enabled.

3. Install TCP/IP.

4. Check TCP/IP settings.

5. Enable the Dial-Up Server.

1. Windows 95 users should download the Microsoft Dial-Up Networking 1.3 Upgrade for Windows 95 from the Microsoft Web site at http://www.microsoft.com/Windows95/downloads/ before performing these steps. Windows 98 includes this update.

2. Click Start, Settings, Control Panel, and then double-click the Network icon.

3. Look in the list of installed network components for an entry named Dial-Up Adapter. If this entry exists, skip the remainder of these steps, and continue with the following section.

4. Select Adapter and click Add.

5. Select Microsoft as the manufacturer, and select Dial-Up Adapter as the network adapter.

1. Click Start, Settings, Control Panel, and then double-click the System icon.

2. Ensure Dial-Up Adapter is enabled.

a) Click the Device Manager tab, and then double-click Network adapters.

b) Double-click Dial-Up Adapter.

c) On the General tab, confirm that the configuration listed as Original Configuration (Current) is selected in Windows 95 or that the Disable in this hardware profile and Remove from this hardware profile are unchecked in Windows 98.

3. Repeat step 2 for all Dial-Up Adapters listed.

1. Click Start, Settings, Control Panel, and then double-click the Network icon.

2. Look in the list of installed network components for an entry named TCP/IP -> Dial-Up Adapter. If this entry exists, skip to the next section.

3. On the Configuration tab, click Add.

4. Select Protocol, and then click Add.

5. Select Microsoft as the manufacturer, select TCP/IP as the network protocol, and then click OK.

1. Click Start, Settings, Control Panel, and then double-click the Network icon.

2. In the list of installed network components on the Configuration tab, double-click Dial-Up Adapter.

3. On the Bindings tab, select only one entry that includes TCP/IP. (If it is displayed, select the entry named TCP/IP -> Dial-Up Adapter. Otherwise, select TCP/IP.)

4. Clear the box next to any other entry that refers to TCP/IP.

5. If you made changes, disconnect the modem's cable, close all programs, and then restart your desktop computer.

6. Click Start, Settings, Control Panel, and then double-click the Network icon.

7. On the Configuration tab, select TCP/IP -> Dial-up Adapter, and then click Properties.

8. Click the IP Address tab, ensure that Obtain an IP address automatically is selected, and then close all dialog boxes.

9. Close all programs and restart your desktop computer.

In order to perform these steps you must have the Dial-Up Networking Upgrade 1.3 installed on your computer.

1. Click Start, Settings, Control Panel, and then double-click the Add/Remove Programs icon.

2. Click Windows Setup, double-click Communications and check the Dial-Up Server option.

3. Double click My Computer on the Windows Desktop.

4. Double click Dial-Up Networking.

5. Click Connections, and then click Dial-Up Server.

6. Select the tab of the modem whose settings you want to change.

7. Select Allow Caller Access.

8. If Share Level Access is enabled in the Access Control tab of the Network control panel you should now use Change Password to protect access to your PC and proceed to the next section. If User Level Access is enabled, you must follow these next steps to create a user account before using a modem to connect your mobile device to your desktop computer.

9. In the Caller Access box, click Add.

10. In the Add User dialog box, enter the user's name. Click Add. You should now see the user's name in the Caller Access list box.

Connect your device to the desktop computer

Additional query words:

Keywords          : kbreadme 
Version           : WINDOWS:3.0
Platform          : WINDOWS 
Issue type        : kbinfo