PC Adm: Microsoft Mail MAILMGR.DLL Version 3.2.0.4074 Update
ID: Q120448
|
The information in this article applies to:
-
Microsoft Mail for Windows, version 3.2
SUMMARY
Microsoft provides a replacement for the MAILMGR.DLL file that is included
with version 3.2 of Microsoft Mail for Windows.
For complete information about obtaining and installing the MAILMGR.DLL
file, see the following sections:
- To download the updated file
- To update your MAILMGR.DLL file
MORE INFORMATION
This update contains MAILMGR.DLL, a replacement for the MAILMGR.DLL file
that is included with version 3.2 of Microsoft Mail for Windows. The
replacement file provides additional enhancements to the original
MAILMGR.DLL file.
This replacement file resolves the following problem that can occur
when you use version 3.2 of Microsoft Mail for Windows:
- The Check Names function fails to properly
resolve partial friendly
names and returns several selections when a unique resolution is
possible. This behavior is most obvious when the GAL is selected as the
default address list and the first and last name of the
intended recipient begin with the same letter.
NOTE: To resolve this problem, two .DLL files must be updated: the
MAILMGR.DLL file (update included in this update) and the MSSFS.DLL
file (update included in MSSFS.EXE on the MSL).
To download the updated file
The following file is available for download from the Microsoft
Download Center. Click the file name below to download the file:
Mailmgr.exe For more information about how to download files from the Microsoft
Download Center, please visit the Download Center at the following Web
address
http://www.microsoft.com/downloads/search.asp
and then click How to use the Microsoft Download Center.
After you download MAILMGR.EXE to a clean directory, run it (by typing
mailmgr at the MS-DOS prompt) to extract the contents of the file.
You should receive the following files:
MAILMGR.DLL (51,696 bytes, dated 07-21-94, 10:48 A.M.)
README.TXT
To replace your MAILMGR.DLL file
- At the MS-DOS command prompt, type the
following and press ENTER
copy <path>:\mailmgr.dll <destination>
where <path> is the drive and directory where you ran the self
extracting MAILMGR.EXE file and <destination> is the drive
and directory where your MAILMGR.DLL file currently resides. For
example, if you ran the self-extracting file from the TEST
directory on drive D, and your MAILMGR.DLL file is located in the
MAILEXE directory on drive C, type the following command:
copy d:\test\mailmgr.dll c:\mailexe
- At the MS-DOS command prompt, type the
following and press ENTER
copy <mailexe>\setup.inf <mailexe>\setupinf.old
where <mailexe> is the complete path to the directory containing
the Microsoft Mail for Windows SETUP.EXE program. For example, if
SETUP.EXE is located in the MAILEXE directory on drive C, type the
following command:
copy c:\mailexe\setup.inf c:\mailexe\setupinf.old
- Using any text editor, edit the
SETUP.INF file. In the [MSMAIL]
section, replace the following line
1, mailmgr.dll,,,, 1993-03-09, !DECOMPRESS,, OLDER,
!READONLY,,,,, SHARED, 51632,,,, 3.2.0.4027,
with:
1, mailmgr.dll,,,, 1994-07-21, !DECOMPRESS,, OLDER,
!READONLY,,,,, SHARED, 51696,,,, 3.2.0.4074,
Save the file and close the text editor.
NOTE: For these changes to affect the entire network, each existing
user must run Setup again.
Additional query words:
3.20 wga
Keywords : MailPCAdm
Version : WINDOWS:3.2
Platform : WINDOWS
Issue type :
|