The information in this article applies to:
SUMMARYDIRECTORY SYNCHRONIZATION ERROR AND STATUS MESSAGES #60 - 118On Microsoft Mail for PC Networks version 3.0 Server Disk 1, there is a file called DIRSYNC.TXT that contains the error codes used in directory synchronization (Dir-Sync) and in the IMPORT utility for Mail. The errors are logged in the DIRSYNC.LOG file.
This is an information message. Because the Import utility is running from the directory server postoffice, the routing for the new postoffice will be direct via an MS-DOS drive. On any other postoffice, the autocreate feature creates a new postoffice that has the same routing that the current postoffice uses to reach the directory server postoffice.
The postoffice for which you are extracting addresses does not have any template information. To get the template information, run the Administrator program, set Config Dir-Sync Requestor Options Templates Receive to Yes and then submit an Import request to the directory server postoffice by selecting Config Dir-Sync Requestor Import. Or you can get the template information from the administrator of the external postoffice, manually insert it into the import file and then run Import to insert the information into your postoffice's data files.
Try the operation again. Then check that there is still a connection to the server and ensure that there is enough disk space to perform the operation. If the problem continues, one of the data files may be locked open. Contact your network vendor to determine how to find and close locked files.
Try the operation again. Then check that there is still a connection to the server. If the problem continues, one of the data files may be locked open. Contact your network vendor to determine how to find and close locked files.
The network name of the postoffice you tried to create with Import's -C autocreate option or with the Administrator program requestor Create-PO option is a reserved name. Select another network name.
You are trying to import users with template information to a postoffice that has no template defined.
The Import utility does create local users. Use the Administrator program Local-Admin commands to define users at your local postoffice. All lines in the import file that contain transactions for local users will be ignored.
You can run the Import utility with the -s and -st options at the directory server postoffice only.
The network name of the postoffice you tried to create with the -C autocreate option already exists. Select another network name.
Only letters and numbers are allowed in network names.
Only letters and numbers are allowed in postoffice names.
Only letters and numbers are allowed in mailbox names.
Check the import file for at least one alias (fullname) that exceeds 30 characters.
The Import utility cannot import template information. Ensure that the Dir-Sync Requestor Options Templates Receive command in the Administrator program is set to Yes, or if you use Import as a stand-alone utility, run the utility with the -T command line option.
Check the import file for fax addresses that are too long. The maximum length of the recipient field in a fax address is 30 characters. The four fax address fields must be in the following order: recipient, location, company, and phone number. The fields are separated by tildes (~).
Check the import file for fax addresses that are too long. The maximum length of the location field in a fax address is 30 characters. The four fax address fields must be in the following order: recipient, location, company, and phone number. The fields are separated by tildes (~).
Check the import file for fax addresses that are too long. The maximum length of the company field in a fax address is 30 characters. The four fax address fields must be in the following order: recipient, location, company, and phone number. The fields are separated by tildes (~).
Check the import file for fax addresses that are too long. The maximum length of the phone number field in a fax address is 22 characters. The four fax address fields must be in the following order: recipient, location, company, and phone number. The fields are separated by tildes (~).
Ensure that the CONFIG.SYS file has FILES=20 (minimum). If the error continues, increase this number.
There is not enough disk space to run the program. Increase the available disk space before continuing.
Ensure that you are running the program on a computer with at least 640K of memory.
Ensure the *.XTN files exist, are correct, and are not corrupt.
Check the import file to ensure local user profile information does not exist for an externally defined user.
Check to make sure the FLAG.GLB file is not locked open.
Wait at least one synchronization cycle and try the operation again. If the problem continues, copy a backup of the MSTTRANS.GLB file. Then ask all requestors to export their address lists.
Ensure that there is still a connection to the server. Also ensure that there is sufficient disk space to receive the mail. Wait at least one directory synchronization cycle and try the operation again. If the problem continues, contact Microsoft Product Support Services.
Ensure that there is still a connection to the server and try the operation again. If the problem continues, contact Microsoft Product Support Services.
Ensure that the computer running the Dispatch program has 640K of memory and that FILES=20 (minimum) in the CONFIG.SYS file. If the problem continues, contact Microsoft Product Support Services.
Check that the foreign requestor did not forget to send an attachment with the system message. If the requestor did send the attachment, wait at least one synchronization cycle as the problem will most likely clear up on its own.
See message 166. Additional query words: 3.00
Keywords : |
|
Last Reviewed: November 3, 1999 © 2000 Microsoft Corporation. All rights reserved. Terms of Use. |