OFF97: Installing Win 98 to New Folder to Tshoot Office Problems

• Microsoft Office 97 for Windows
• Microsoft Windows 98

SUMMARY

This article describes how to install a second copy of Microsoft Windows 98 to a new folder on your computer for troubleshooting problems that arise during installation or usage of the Microsoft Office programs. This is also useful in determining if your current installation of Windows 98 is functioning properly.

For information about installing Microsoft Windows 95 into a new folder, please see the following article in the Microsoft Knowledge Base:

Q178400 OFF97: Installing Win 95 to New Folder to Tshoot Office Problems

Requirements for Installing a Second Copy of Windows 98 to a New Folder

• Approximately 365 megabytes (MB) of free hard drive space for the second copy of Windows 98 (170 MB for the Win98 folder and 195 MB for the Windows 98 installation). If you plan to install Windows programs (such as Office) under the new copy of Windows 98, you will need additional disk space as required by each program.



• The Windows 98 compact disc (CD) or access to the Windows 98 installation files.



• Your Windows 98 Product Key, which is normally located on the Windows 98 CD sleeve. If you are using an Original Equipment Manufacturer (OEM) version of Windows 98, you will need your OEM Product Key, which is located on your Certificate of Authenticity.



• A Windows 98 Startup disk. If you should encounter problems following the instructions below, it may be necessary to use the Windows 98 Startup disk to start the computer.

MORE INFORMATION

Create a Windows 98 Startup Disk

1. Click the Start button, point to Settings, and then click Control Panel.



2. Double-click the Add/Remove Programs icon.



3. Click the Startup Disk tab.



4. Click Create Disk.

How to Install a Second Copy of Windows 98 to a New Folder

1. Click Start, point to Programs, and then click MS-DOS Prompt.



2. At the command prompt, type the following lines, pressing ENTER after each line:




cd
md w98flat

3. Insert the Windows 98 CD into the CD-ROM drive.



4. At the command prompt, type the following line, and then press ENTER:




copy <drive>:\win98\*.* c:\w98flat


where <drive> is the drive letter assigned to your CD-ROM drive.


5. At the command prompt, type Exit and press ENTER.



6. Restart your computer. Press and hold down the CTRL key until the Windows 98 Startup Menu appears.



7. On the Windows Startup menu, select the option for Command Prompt Only, and then press ENTER.



8. Make a backup copy and rename the system files in case you decide to return to your original installation of Windows 98 later. To do so, type the following lines at the command prompt. Press ENTER after each line.




attrib -s -h -r bootlog.txt
attrib -s -h -r bootlog.prv
attrib -s -h -r detlog.txt
attrib -s -h -r msdos.sys
attrib -s -h -r setuplog.txt
attrib -s -h -r system.1st
copy autoexec.bat *.xxx
copy config.sys *.xxx
ren bootlog.prv bootlog2.xxx
ren bootlog.txt *.xxx
ren detlog.txt *.xxx
ren msdos.sys *.xxx
ren setuplog.txt *.xxx
ren system.1st *.xxx


NOTE: If you receive a "File not found" error message entering any of the previous lines, ignore the error message and proceed to the next line.

NOTE: The Program Files folder will not be changed because the Program Files folder was not renamed.


9. Type the following line, and then press ENTER:




cd\w98flat

10. To run the Windows 98 Setup program, type Setup, and then press ENTER.
    
    During the Windows 98 setup, specify a new folder for the Windows 98 installation. Make sure not to use the folder for your current installation of Windows 98.

How to Restore the Previous Copy of Windows 98

1. Restart your computer. Press and hold down the CTRL key until the Windows 98 Startup Menu appears.



2. On the Windows Startup menu, select the option for Command Prompt Only, and then press ENTER.



3. At the command prompt, type the following lines, pressing ENTER after each line, type y and press ENTER:




deltree autoexec.bat
deltree bootlog.txt
deltree bootlog.prv
deltree config.sys
deltree detlog.txt
deltree msdos.sys
deltree setuplog.txt
deltree system.1st
ren bootlog2.xxx bootlog.prv
ren autoexec.xxx *.bat
ren bootlog.xxx *.txt
ren config.xxx *.sys
ren detlog.xxx *.txt
ren msdos.xxx *.sys
ren setuplog.xxx *.txt
ren system.xxx *.1st


NOTE: If you receive a "File not found" error message entering any of the previous lines that use the ren command, ignore the error message and proceed to the next line.

NOTE: When you press ENTER after typing each of the following deltree commands, you should be prompted to confirm that you want to delete the folder. If this prompt does not appear, you may have typed the command incorrectly


4. At the command prompt, type the following lines, pressing ENTER after each line. Note that you will be asked to confirm each line when you press ENTER. Type




deltree w98flat deltree <directory>


where <directory> is the name of the folder where the new copy of Windows 98 is installed. If your new Windows 98 directory is called "win98", the syntax would look like this:

deltree win98

5. Press CTRL+ALT+DEL to restart the computer. When the computer restarts, your original copy of Windows 98 will be restored.

Additional query words: tshoot SOL separate

Keywords : kbdta
Version : WINDOWS:97
Platform : WINDOWS
Issue type : kbhowto