WD97: All Workstations Not Using Same Word Preference/Option Settings
ID: Q196759
|
The information in this article applies to:
-
Microsoft Word 97 for Windows
SYMPTOMS
After you install Word for Windows on a server, all or some of the
workstations may not use the option or preference settings you selected
during Setup. Instead, these workstations may all use the same set of
defaults, such as the default font or Most Recently Used (MRU) list on the
File menu.
CAUSE
This problem occurs if the Normal.dot file exists in the network server
program directory, instead of in the user directory that you specified
during the Workstation Setup.
Word (not Word Setup) creates the Normal.dot files in the server program
directory. This occurs if the network administrator (or someone who has
read, write, and create privileges in the Word program directory on the
server) runs Word from the server installation before running a
Workstation
Setup to install Word on the workstation. Before you run the Workstation
Setup, no references to the file locations exist in the Windows program
directory, so when you quit Word the first time, it stores the Winword.opt
and the Normal.dot files on the server in the directory where the
Winword.exe program is located (the default location).
After the Normal.dot file exists on the server, Word uses these files
every
time it starts from any workstation, even if you have run a Workstation
Setup and created a reference that points to another Normal.dot location.
This happens because, as Word starts, it checks for these files in the
directory where the Winword.exe file resides. If it finds Winword.opt or
Normal.dot in this location, it uses those files and does not read your
reference file to attempt to find them in another location.
NOTE: In some cases, it is desirable to have everyone use the same
Normal.dot file and prevent any changes being made.
Infrequently, this problem also occurs if you ran the Workstation Setup
at your workstation while you were running Windows from a different
location (that is, from a location other than the one specified in your
network logon script).
NOTE: Word Setup does not create the Normal.dot file. Word creates new
versions of this file any time you run the program and the file is not
located. Therefore, this is a network administration issue rather than a
Word Setup issue.
RESOLUTION
Perform all three of the following steps to resolve this problem and
restore each user's preference and option settings in Word:
- Quit all instances of Word running from the server. Rename or delete the Normal.dot files in the network server directory.
- Make sure the Word program directory on the network server and all
files in that directory are flagged as read-only and shareable. You
should not have write privileges in this server directory before you
perform the Workstation Setup at the workstation.
- Make sure you run a Workstation installation of Word at every
workstation where the user has administrative rights (that is, full
access to the Word program directory on the server). This process
references that point to the correct location for your user's
Normal.dot file.
MORE INFORMATION
This section contains a description of the Normal.dot file and a
discussion of the network installation of Word as it pertains to the problem addressed in this article.
Normal.dot
The default document template that stores macros, toolbars, menus, keystrokes, AutoText, and AutoCorrect entries. This file should be located in the user's Template directory and is created after the user makes a change to one of the items mentioned above. This file is not created by Setup. It is referenced in the Windows registry file.
Overview: Network Setup of Word
NOTE: This discussion assumes that you have a working knowledge of
network operations and terminology. For network-specific information,
see your network documentation.
To install Word so it runs from a network file server, go to a
workstation and connect to the file server. Run the administrator's
installation of Word (type "setup /a" at the command line). When Setup
prompts you for the network directory for the main Word program,
specify a path on the file server. Setup copies all the program files
to this location.
IMPORTANT: DO NOT RUN WORD AT THIS POINT! If you do, the problems
described at the beginning of this article may occur. Before you run
Word, you must first perform the following two steps:
- Set the access privileges to read-only and shared for the server
directories in which you installed Word. Refer to your MS-DOS or
network operating system documentation for more information.
- Run the workstation installation of Word at each workstation. This
registers the Word program with your local Windows installation and
creates references to file locations. If you do not run a
workstation installation before you run Word from the network
server, Word runs, but some operations do not function correctly,
such as the spelling checker, grammar checking, and object linking
and embedding (OLE ).
NOTE: If you are running Windows from a network server, the first
workstation installation of Word makes all the necessary Windows-level
changes. This means you need all access privileges to the shared
Windows program directory, and that directory must not be read-only.
Additional query words:
most-recently-used info
Keywords : word97
Version : WINDOWS:97
Platform : WINDOWS
Issue type : kbprb
|