Recovering From Boot Failure Affecting Mirrored Drives

• Microsoft Windows NT Server versions 3.5, 3.51, 4.0

SUMMARY

When a boot failure on a system with a mirrored boot drive occurs, and the failure is caused by a problem that has affected both the primary and a mirror, such as bad or corrupt device drivers or other changes to the system, using a Fault Tolerance boot floppy does not allow you to boot (since both drives have the same problem). In this case, the normal procedure is to boot to an alternative operating system, such as MS-DOS or another installation of Windows NT, and use it for possible recovery. However, if your boot drive is mirrored, this procedure is not possible, unless you manually break the mirror.

MORE INFORMATION

To manually break the mirror, use a disk editor to change the partition table and the byte that indicates the partition type. Norton's Diskedit or another comparable utility can be used for this purpose. The partition table is in the first physical sector on a hard drive.

The partition entries start at an offset. On a mirrored drive, this byte is either 0x86 (for FAT partition) or 0x87 (for NTFS partition). The byte needs to be changed to 0x06 (for FAT partition) or 0x07 (for NTFS partition). To do this (using Norton Diskedit version 5.0 or later), use the following procedure:

CAUTION: Using a disk editor to directly change the information on your drive is dangerous and can result in furthur drive corruption if it is not done properly. Use this procedure as a last resort.

1. Boot from an MS-DOS bootable floppy disk that contains a copy of Norton Diskedit. Make sure that the floppy disk includes the NLIB200.RTL file.



2. Run Diskedit.



3. From the Object menu, select Drive.



4. From the Drive dialog box, select Physical drive. The default is Logical drive.



5. Select the physical hard drive that is the primary from the mirror set (this is normally Drive 1).



6. From the Object menu, select Partition Table. From the View menu, select "as Partition table" to view the following table:

---------------------------------------------------------------------------
|       |    |  Starting Location |  Ending Location   |Relative|Number of|
|System |Boot|Side Cylinder Sector|Side Cylinder Sector|Sectors |Sectors  |
|  ?    |Yes | 1       0       1  |  63   509      32  |      32|  1044448|
| unused|No  | 0       0       0  |   0     0       0  |       0|        0|
| unused|No  | 0       0       0  |   0     0       0  |       0|        0|
| unused|No  | 0       0       0  |   0     0       0  |       0|        0|
---------------------------------------------------------------------------

   Each entry in this table is a partition. The row that has a Boot value
   of "Yes" is generally your mirror partition. The example above only has
   the one partition, but the other entries may have values if the disk has
   partitions other than the mirror. The system value is based upon
   Diskedit's interpretation of the partition type byte. In the table
   above, it lists a "?", as it does not understand type 0x86 and 0x87. 

1. Use the arrow keys to move to the "?" entry in the System column.



2. Press the space bar to change the value from "?" to "BIGDOS" for FAT partitions or "HPFS" for NTFS partitions (both HPFS and NTFS use the same partition type ID - 0x7. Diskedit does not differentiate between the two types).



3. From the Edit menu, select Write Changes.



4. Exit Diskedit.



5. Reboot the system with either an MS-DOS floppy disk or from the Windows NT Setup disks. Your boot drive should be accessible from MS-DOS (if it is FAT) or to Windows NT Setup (if it is NTFS).

Additional query words: filesys ntfaqset

Keywords :
Version : WinNT:3.5,3.51,4.0
Platform : WINDOWS
Issue type :