SMB Block Size Negotiation When Copying Files with Windows NT Explorer

ID: Q223140


The information in this article applies to:
  • Microsoft Windows NT Server version 4.0
  • Microsoft Windows NT Workstation version 4.0

IMPORTANT: This article contains information about editing the registry. Before you edit the registry, make sure you understand how to restore it if a problem occurs. For information about how to do this, view the "Restoring the Registry" Help topic in Regedit.exe or the "Restoring a Registry Key" Help topic in Regedt32.exe.

SUMMARY

When you copy or move a file, the negotiated Server Message Block (SMB) size is different. The block size depends on a number of factors including:

  • Whether Windows NT Explorer or an MS-DOS command prompt is used to issue the command.


  • Which direction the file is being moved or copied to (that is, copying a file from your computer to another computer versus your computer copying a file from another computer back to your own computer.)


When you use Windows NT Explorer to copy a file from the client to a remote computer, data is typically transfered in Core mode in 4 KB blocks.

When you use Windows NT Explorer to copy a file from the remote computer back to the client, data is typically transfered in Raw mode in 60 KB blocks.

When you use an MS-DOS command prompt command to copy a file in either direction, data is generally transfered in Raw mode. Because Raw mode typically uses a 60-64 KB transfer rate, and Core mode typically uses 4 KB, a Raw-mode transfer is faster.


MORE INFORMATION

The factors listed below determine which transfer mode is chosen. However, in this example, what's happening is not getting exclusive use of the Virtual Circuit (VC), which is created when setting up the connection between the two computers. When you cut or copy a file in Windows NT Explorer, make a folder, or perform some other file system changes, Windows NT Explorer will show that change quickly by updating the display. The update in the display is triggered by a call called ChangeNotify.

When copying a file to a remote computer, a long distance ChangeNotify call is triggered. This call goes over the network. This call also prevents getting exclusive use of the VC to copy the file. When copying a file from a remote computer back to the client (command issued locally), the ChangeNotify call is still triggered, but it's now a local call. So the call is not sent over the wire, therefore, the copy operation gets exclusive use of the VC.

Because ChangeNotify is not called for to copy or move a file when you use an MS-DOS command prompt command, these transfers typically use Raw mode.

From the specifications for Core versus Raw mode data transfers:

The Windows NT redirector has the following requirements for performing raw mode I/O, all of which must be satisfied for raw mode I/O to occur.
  • The Server Message Block (SMB) protocol negotiated between the client and server must support Raw mode.


  • The server must be configured to support Raw mode.


  • The client redirector must be configured to allow Raw mode.


  • No other SMB requests are pending on the same Virtual Circuit (VC).


  • The I/O is not on a blocking named pipe.


  • For a READ request: the requested data size is equal to or greater than 2 times the currently configured request buffer size, and the read offset is not past the redirector's currently configured end-of-file.


  • For a WRITE request: the requested data size is equal to or greater than 1.5 times the currently configured request buffer size, and the write offset is not more than approximately 1 MB past the current end-of-file.


  • The I/O is to take no longer than 5 seconds to complete."


Core Mode Data Transfer:

When writing data in Core mode, as in file copy to a remote server, size of data blocks transferred is 4KBytes by default. This can be modified using the following registry parameter on the remote server side.

WARNING: Using Registry Editor incorrectly can cause serious problems that may require you to reinstall your operating system. Microsoft cannot guarantee that problems resulting from the incorrect use of Registry Editor can be solved. Use Registry Editor at your own risk.

For information about how to edit the registry, view the "Changing Keys and Values" Help topic in Registry Editor (Regedit.exe) or the "Add and Delete Information in the Registry" and "Edit Registry Data" Help topics in Regedt32.exe. Note that you should back up the registry before you edit it. If you are running Windows NT, you should also update your Emergency Repair Disk (ERD).
To increase the buffer size, edit the SizReqBuf registry value using the following steps:
  1. Start Registry Editor (Regedt32.exe or Regedit.exe).


  2. Go to the following registry subkey:
    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services \LanmanServer\Parameters NOTE: The above registry key is one path; it has been wrapped for readability.


  3. Create the SizReqBuf value using the following information:
    
       Value Name: SizReqBuf
       Data Type : REG_DWORD
       Data      : 512 - 65536 (bytes in decimal)
       Default   : 4096 
    NOTE: Small buffers use less memory and large buffers can improve performance. The exact value that works best in a given environment will depend on the specific configuration of that environment, but 14596 is a value that has been shown to work well in a fairly standard Ethernet environment. Setting this parameter to the maximum value will make server to transfer data in 60 KB blocks.


  4. Close Registry Editor and restart the Server service.



REFERENCES

Q152081 Use of Raw Data Transfer Mode Influenced by Application

Additional query words: data transfer raw core SMB negotitate slow

Keywords :
Version : winnt:4.0
Platform : winnt
Issue type : kbinfo


Last Reviewed: April 30, 1999
© 2000 Microsoft Corporation. All rights reserved. Terms of Use.