Platform SDK: TAPI

lineMakeCall

The lineMakeCall function places a call on the specified line to the specified destination address. Optionally, call parameters can be specified if anything but default call setup parameters are requested.

LONG WINAPI lineMakeCall(
  HLINE hLine,                         
  LPHCALL lphCall,                     
  LPCSTR lpszDestAddress,              
  DWORD dwCountryCode,                 
  LPLINECALLPARAMS const lpCallParams  
);

Parameters

hLine
A handle to the open line device on which a call is to be originated.
lphCall
A pointer to an HCALL handle. The handle is only valid after the LINE_REPLY message is received by the application indicating that the lineMakeCall function successfully completed. Use this handle to identify the call when invoking other telephony operations on the call. The application is initially the sole owner of this call. This handle is void if the function returns an error (synchronously or asynchronously by the reply message).
lpszDestAddress
A pointer to the destination address. This follows the standard dialable number format. This pointer can be NULL for non-dialed addresses (as with a hot phone) or when all dialing is performed using lineDial. In the latter case, lineMakeCall allocates an available call appearance that would typically remain in the dialtone state until dialing begins. Service providers that have inverse multiplexing capabilities can allow an application to specify multiple addresses at once.
dwCountryCode
The country code of the called party. If a value of 0 is specified, a default is used by the implementation.
lpCallParams
A pointer to a LINECALLPARAMS structure. This structure allows the application to specify how it wants the call to be set up. If NULL is specified, a default 3.1 kHz voice call is established and an arbitrary origination address on the line is selected. This structure allows the application to select elements such as the call's bearer mode, data rate, expected media mode, origination address, blocking of caller ID information, and dialing parameters.

Return Values

Returns a positive request identifier if the function is completed asynchronously, or a negative error number if an error occurs. The dwParam2 parameter of the corresponding LINE_REPLY message is zero if the function succeeds or it is a negative error number if an error occurs. Possible return values are:

LINEERR_ADDRESSBLOCKED, LINEERR_INVALLINEHANDLE, LINEERR_BEARERMODEUNAVAIL, LINEERR_INVALLINESTATE, LINEERR_CALLUNAVAIL, LINEERR_INVALMEDIAMODE, LINEERR_DIALBILLING, LINEERR_INVALPARAM, LINEERR_DIALDIALTONE, LINEERR_INVALPOINTER, LINEERR_DIALPROMPT, LINEERR_INVALRATE, LINEERR_DIALQUIET, LINEERR_NOMEM, LINEERR_INUSE, LINEERR_OPERATIONFAILED, LINEERR_INVALADDRESS, LINEERR_OPERATIONUNAVAIL, LINEERR_INVALADDRESSID, LINEERR_RATEUNAVAIL, LINEERR_INVALADDRESSMODE, LINEERR_RESOURCEUNAVAIL, LINEERR_INVALBEARERMODE, LINEERR_STRUCTURETOOSMALL, LINEERR_INVALCALLPARAMS, LINEERR_UNINITIALIZED, LINEERR_INVALCOUNTRYCODE, LINEERR_USERUSERINFOTOOBIG.

Remarks

If LINEERR_INVALLINESTATE is returned, the line is currently not in a state in which this operation can be performed. A list of currently valid operations can be found in the dwLineFeatures member (of the type LINEFEATURE_) in the LINEDEVSTATUS structure. Calling lineGetLineDevStatus updates the information in LINEDEVSTATUS. If LINEERR_DIALBILLING, LINEERR_DIALQUIET, LINEERR_DIALDIALTONE, or LINEERR_DIALPROMPT is returned, none of the actions otherwise performed by lineMakeCall have occurred; for example, none of the dialable address prior to the offending character has been dialed, no hookswitch state has changed, and so on.

After dialing has completed, several LINE_CALLSTATE messages are usually sent to the application to notify it about the progress of the call. No generally valid sequence of call-state transitions is specified, as no single fixed sequence of transitions can be guaranteed in practice. A typical sequence can cause a call to transition from dialtone, dialing, proceeding, ringback, to connected. With non-dialed lines, the call can typically transition directly to connected state.

An application has the option to specify an originating address on the specified line device. A service provider that models all stations on a switch as addresses on a single line device allows the application to originate calls from any of these stations using lineMakeCall.

The call parameters allow the application to make non-voice calls or request special call setup options that are not available by default.

An application can partially dial using lineMakeCall and continue dialing using lineDial. To abandon a call attempt, use lineDrop.

After lineMakeCall returns a success reply message to the application, a LINE_CALLSTATE message is sent to the application to indicate the current state of the call. This state is not necessarily LINECALLSTATE_DIALTONE.

Requirements

  Windows NT/2000: Requires Windows NT 4.0 SP3 or later.
  Windows 95/98: Requires Windows 95 or later.
  Version: Requires TAPI 1.3 or later.
  Header: Declared in Tapi.h.
  Library: Use Tapi32.lib.
  Unicode: Implemented as Unicode and ANSI versions on all platforms.

See Also

TAPI 2.2 Reference Overview, Basic Telephony Services Reference, Dialable Addresses, LINE_CALLSTATE, LINE_REPLY, LINECALLPARAMS, LINEDEVSTATUS, lineDial, lineDrop, lineGetLineDevStatus