CryptEncrypt

This function is used to encrypt data. The algorithm used to encrypt the data is designated by the key held by the cryptographic service provider (CSP) module, which is referenced by the hKey parameter.

At a Glance

Header file:	Wincrypt.h
Windows CE versions:	2.10 and later

Syntax

BOOL CRYPTFUNC CryptEncrypt( HCRYPTKEY hkey, HCRYPTHASH hHash, BOOL Final, DWORD dwFlags, BYTE *pbData, DWORD *pdwDataLen, DWORD dwBufLen );

Parameters

hKey

[in] Handle to the key to use for the encryption. An application obtains this handle by using either the CryptGenKey or the CryptImportKey function.

This key specifies the encryption algorithm that is used.

hHash

[in] Handle to a hash object. This parameter is used only if a hash of the data is to be computed at the same time the encryption is being performed. For more information, see Remarks.

If no hash is to be done, this parameter must be zero.

Final

[in] Boolean value that specifies whether this is the last section in a series being encrypted. This should be TRUE if this is the last or only block, and FALSE if it is not. For more information, see Remarks.

dwFlags

[in] Specifies a bitmask of flags. This parameter is reserved for future use and should always be zero.

pbData

[in/out] Pointer to the buffer that holds the data to be encrypted. After the encryption has been performed, the encrypted data is placed back in this same buffer.

The size of this buffer is specified by dwBufLen. The number of bytes of data to be encrypted is specified by pdwDataLen.

This parameter can be NULL if all you are doing is determining the number of bytes required for the returned data.

pdwDataLen

[in/out] Pointer to the data length. Before calling this function, the caller should set this parameter to the number of bytes to be encrypted. Upon return, this address will contain the number of bytes of encrypted data.

If the buffer specified by pbData is not large enough to hold the data, the function returns the ERROR_MORE_DATA error code (through GetLastError) and stores the required buffer size, in bytes, into the variable pointed to by pdwDataLen.

If pbData is NULL, then no error is returned, and the function stores the size of the data, in bytes, in the variable pointed to be pdwDataLen. This lets an application determine the correct buffer size unambiguously.

When a block cipher is used, this data length must be a multiple of the block size, unless this is the final section of data to be encrypted and the Final flag is TRUE.

dwBufLen

[in] Specifies the number of bytes in the pbData buffer.

Note that, depending on the algorithm used, the encrypted text can be slightly larger than the original plaintext. In this case, the pbData buffer needs to be sized accordingly.

As a rule, if a stream cipher is used the ciphertext will be the same size as the plaintext. If a block cipher is used, the ciphertext will be up to a "block length" larger than the plaintext.

Return Values

TRUE indicates success. FALSE indicates failure. To get extended error information, call GetLastError. Common values for GetLastError are described in the following table. The error values prefaced by "NTE" are generated by the particular CSP you are using.

Value	Description
ERROR_INVALID_HANDLE	One of the parameters specifies an invalid handle.
ERROR_INVALID_PARAMETER	One of the parameters contains an invalid value. This is most often an illegal pointer.
NTE_BAD_ALGID	The hKey session key specifies an algorithm that this CSP does not support.
NTE_BAD_DATA	The data to be encrypted is invalid. For example, when a block cipher is used and the Final flag is FALSE, the value specified by pdwDataLen must be a multiple of the block size.
NTE_BAD_FLAGS	The dwFlags parameter is nonzero.
NTE_BAD_HASH	The hHash parameter contains an invalid handle.
NTE_BAD_HASH_STATE	An attempt was made to add data to a hash object that is already marked "finished."
NTE_BAD_KEY	The hKey parameter does not contain a valid handle to a key.
NTE_BAD_LEN	The size of the output buffer is too small to hold the generated ciphertext.
NTE_BAD_UID	The CSP context that was specified when the key was created cannot be found.
NTE_DOUBLE_ENCRYPT	The application attempted to encrypt the same data twice.
NTE_FAIL	The function failed in some unexpected way.
NTE_NO_MEMORY	The CSP ran out of memory during the operation.

Remarks

If data is to be hashed and encrypted simultaneously, a handle to a hash object can be passed in the hHash parameter. The hash value will be updated with the plaintext passed in. This option is useful when generating signed and encrypted text.

Before calling CryptEncrypt, the application should obtain a handle to the hash object by calling the CryptCreateHash function. After the encryption is complete, the hash value can be obtained through the CryptGetHashParam function or the hash can be signed using the CryptSignHash function.

When a large amount of data needs to be encrypted, it can be done in sections. This is done by calling CryptEncrypt repeatedly. The Final parameter should be set to TRUE only on the last invocation of CryptEncrypt, so the encryption engine can properly finish the encryption process. The following extra actions are performed when Final is TRUE:

υIf the key is a block cipher key, the data will be padded to a multiple of the block size of the cipher. To find the block size of a cipher, use CryptGetKeyParam to get the KP_BLOCKLEN parameter of the key.
υIf the cipher is operating in a chaining mode, the next CryptEncrypt operation will reset the cipher's feedback register to the KP_IV value of the key.
υIf the cipher is a stream cipher, the next CryptEncrypt will reset the cipher to its initial state.